AUTONET TV

Smooth Operator (Shocks and Struts)

Few of us ever drive somewhere without encountering some pretty rough roads, and it's amazing how well our vehicles are able to smooth out the ride. Thank your shocks and struts.

The two parts are similar.  Some cars have shocks in the rear, and struts in the front.  Others have struts all around.  A shock absorber uses a cylinder filled with gas or liquid that's connected to your vehicle's frame and axle.  When your vehicle encounters an imperfection in the road, the shock dampens the motion. 

A strut is essentially a shock absorber mounted inside a spring and can support more weight than a shock by itself.

Shocks and struts take a lot of punishment and wear out.  When they do, your tires are not contacting the road as much as they should, and that can result in a bumpy, unstable ride. Worn-out shocks and struts also transfer the impacts of road imperfections directly to your vehicle's body which can cause further damage to other parts.

You can tell when your shocks and struts are wearing out when your vehicle's ride is bouncy, you feel the bumps and body motion a lot more than you used to, or you may see fluid leaking from the areas near the wheels.

How often your shocks and struts need replacing depends on what surfaces you drive on, how far they've traveled, and how long they've been on the vehicle.  Our technicians can check the condition of your shocks and struts and advise you when they need to be changed.  Shocks and struts should always be changed in pairs.  

Because shocks and struts wear out gradually over a long time and distance, experts recommend you have them checked at least once a year.  Plus, if you know you've recently hit something especially hard in the road, you should have your suspension checked just to make sure it's ok.

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

STRAIGHT TALK ABOUT STEERING (Loose Steering)

Perhaps you've heard someone use the term "loose steering." And it's pretty much what it sounds like.  You turn the steering wheel and the vehicle's wheels don't seem to go exactly where you thought you were pointing them.  You have to constantly make steering adjustments. 

Loose steering is sloppy steering, and it can be a safety hazard.  You need to be able to control your vehicle with pretty much the same precision as the way it was when it came off the assembly line.  

If the steering in your vehicle is starting to feel loose and sloppy, there may be some significant suspension issues that need examining by a trained technician.

How do you know if your vehicle needs to be looked at? Try turning the steering wheel and see how much play is in it.  One rule of thumb: if you can turn it the distance of a quarter and a dime placed side by side without seeing the outside wheels move, it's time to have it inspected by one of our technicians.

Our Triple A Automotive technician will examine those components that are supposed to work together to make sure your steering is tight and precise.  They are linked together by things called (of course) linkages.

When these linkage components were new, they all fit together tightly and moved together to make sure your wheels responded quickly and precisely to your movements of the steering wheel.   

But hit a few potholes, travel over a couple of rough railroad tracks and those metal components can be damaged or bent.  Given enough time, they will simply wear out. Our trained Triple A Automotive technician can inspect all of those parts and determine what needs to be repaired and/or replaced.  

Keep your steering tight.  Loose or sloppy steering can be dangerous.  Thank goodness it usually warns you in plenty of time before it fails completely. Just straight talk… about steering.

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

How Cool is That! (Coolant level sensor replacement)

Your vehicle’s engine runs hot.  It should, since it’s a series of little explosions that create the power that gets you going where you want to go.  To keep the engine cool, engineers have designed wonderful cooling systems that use liquid coolant, hoses, and a radiator to transfer the heat from the engine to the outside air. 

In order for the system to work right, it has to have the right amount of that liquid coolant in it.  So that you know when the coolant has dipped below the correct amount, there is a sensor that keeps an eye on it.  When the coolant gets low, that sensor lights up a signal on the dash to alert you.  It may literally say “Check Coolant” or it may have a picture that looks like an old-style bulb thermometer sitting in liquid.  Your owner’s manual will usually tell you exactly what the one in your vehicle looks like.

If that sensor system isn’t working right, you could wind up driving for a long time with not enough coolant in the engine, and the excess heat can cause some extensive—and expensive—damage. 

There are a couple of ways you will know if something’s wrong with your coolant level sensor.  One is when you top off the coolant tank, and the low coolant light stays on.  If you suspect yours might be having a problem, bring it in so we can thoroughly check your coolant system.

If it is a sensor, we can run a test to see where the problem is in your cooling system.  It could be a bad sensor, but it also could be that there is something causing your coolant level to be low.  If the sensor needs replacing, the technician will replace it, fill your coolant level to the manufacturer’s recommended level, and test for any leaks in the system.  Really, how cool is that?

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

test

The Little Valve that Could (PCV Valve Replacement)

It's easy to get letters like PVC and PCV mixed up.  PVC is a plastic that's used in a lot of things, especially plumbing pipes.  And PCV is a valve that helps your engine burn off excess fumes rather than having them pollute our atmosphere. 

PCV stands for positive crankcase ventilation.  When your engine ignites gasoline in the cylinders, some of the gases produced make their way into the crankcase, where oil is held to lubricate the engine.  In earlier days, those gases would be vented out through a hose and go directly into the air.  It was a waste of gasoline (since about three-fourths of the gases were unburned fuel) and a nasty source of pollution.

So engineers devised a one-way valve that directed those gases back into the engine's air intake system to be burned again.  After a while, the PCV valve can get clogged up with gummy oil.  Not only does that reduce the recirculation of the gases, but it can also cause pressure in the crankcase to increase and possibly lead to an oil leak.

Signs your PCV valve has failed are oil leaks around the engine compartment or under your vehicle and poor engine performance. Your fuel economy will get worse. If you notice those signs, we can check your PCV valve. 

At the same time a technician inspects the PCV valve, they'll also check the vacuum hose that runs back to the air intake.  Plus, they'll make sure the vehicle doesn't have any other engine problems that might be contributing to your issues. 

Many technicians recommend replacing your PCV valve with each major tune-up, so you get ahead of any problems before they develop.  Now that you're an expert on PCV, it may be time to check out those PVC pipes in your bathroom!

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

Not So Cool (Air Conditioning Systems)

There's nothing quite like getting in your vehicle on a hot day, switching on the air conditioning and having warm air blow out of the vents.  You may have had no problem for months and then, one day, you are driving around in a sauna. You're hot stuff, but not in a good way!

So what goes wrong when the AC isn't working? It could be a lot of things because the system has many different components.  One thing that's a common cause is the vehicle is low on refrigerant (it used to be called Freon).  If that's the case, it's not as simple as simply adding more.  Sure, it may fix it quickly for a short time, but it's more likely than not that the refrigerant will just leak out again.

The original Freon used in air conditioners was destroying the Earth's ozone layer, so that's not used much any more.  But the one that's currently used also contributes to global warming, so it's important that as little of that escapes as possible.  So a technician will determine if there's a leak in your system, where it is and fix that before adding new refrigerant. 

Your vehicle also has an evaporator or two, and those can fail.  Leaks are often the problem with them as well.  The big component that can go bad is the compressor, often a victim of age, wear or neglect. 

A technician will also check to see that the blower is working correctly.  That's what blows that cool air into the cabin.  Sometimes the motor will fail, a relay will go bad or a fuse will blow.  As you can see, there are lots of different parts involved here! 

The good news is that your vehicle's service facility has the special equipment to recover the refrigerant and check the system's pressure, both vital to properly servicing the air conditioning system.

As with many vehicle components, regular maintenance can go a long way to minimizing problems in the air conditioning system. It can reduce the chance of the compressor having to be replaced, too.  Pretty cool, huh?

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com